Complete Guide on Resetting Jeep Renegade Oil Life Meter

In order to help you maintain the Jeep Renegade, an oil life meter helps you monitor the oil condition. It lets you know when the Jeep Renegade needs its next oil change. 

Sometimes it needs to be reset, especially after changing oil. It can be done easily by turning the ignition on and pressing the accelerator methodically. 

No worries, you will get to know step-by-step how to change the oil and reset the oil life meter in your Jeep Renegade. 

How to Reset the Jeep Renegade Oil Life Meter?

The oil life meter indicates when it is necessary to change the oil. When the oil level in your Jeep gets too low, the light on this meter flashes to remind you of the oil change. 

Along with the oil light, you will also receive a warning named Oil Change Due. Even after you have changed the oil, this light will remain illuminated until you manually reset the oil life meter. 

Every time you change the oil on your Jeep Renegade, it is recommended to reset the oil life meter as well. 

Resetting the oil life meter timely will give you accurate notifications of when the oil needs to be changed next. Follow these simple steps to reset the Jeep Renegade oil life meter:

1. Park the Jeep Renegade on a level surface.
2. Ensure that the parking brake is engaged and the gear shifter is set to Park.
3. Without starting the engine, turn the ignition switch to the ON position.
4. Make sure not to step on the brake pedal.
5. Press and release the accelerator pedal three times within ten seconds.
6. Every time you press on it, the oil light on the dashboard will disappear.
7. Afterwards, turn the ignition switch OFF and then within a few moments, turn it back ON again.
8. Start the engine this time and check if the oil life meter has been reset and the light is gone.
9. The instrument panel will display the message Oil Change Reset if the reset is successful.

How Often Does a Jeep Renegade Need an Oil Change?

If you don’t want to rely on the oil life indicator to remind you of an oil change, you can schedule a routine for it.

Usually, a Jeep Renegade needs an oil change after driving 3000-5000 miles.

If the Jeep uses synthetic 0W-20 engine oil, the recommended driving distance until an oil change is maximum 5000 miles. 

However, if you use synthetic oil of 0W-30 SN PLUS in your Jeep, you can drive more mileage without an oil change. 

Generally, a Jeep with a turbo engine uses this kind of oil. So, these Jeep Renegade can go up to 10,000 miles without an oil change each time. 

How to Turn Off the Oil Light on Jeep Renegade?

The most common way of turning off the oil light in Jeep Renegade is to change the oil. 

For good measure, reset the oil life meter in order to make sure the indicator oil light is not illuminated anymore.

If there are issues with the sensor or the oil tank system, the oil light might not be turned off after this. 

In that case, the only way to turn it off is to call an expert or a professional to help turn it off. 

They can discover the problem with the other components and solve it accordingly. 

Once taken care of, the oil light on the Jeep renegade will turn off completely until the next oil change.

How to Change the Oil on Your Jeep Renegade?

Knowing how to change the oil on your Jeep Renegade is imperative. You shouldn’t reset the oil life meter before changing the oil. 

Not only will it fail to solve the problem but also it risks severely damaging the engine. 

So, let’s take a look at how you can change the oil of your Jeep Renegade without any trouble.

1. Check the owner’s manual to identify which synthetic oil the Jeep uses between the 0W-20, 10W-30, and 5W-40.
   Get the exact same oil type your Jeep Renegade requires.
2. Drive the Jeep onto a ramp or raise it with jacks to get under the jeep with ease.
3. Position the catch pan directly beneath the oil drain pan in order to properly collect and dispose of the oil.
4. Remove the plug with the help of a wrench and wait for the oil to drain off.
5. Replace the drain plug once all the oil is drained and tighten the socket again.
6. Get the old oil filter out of the jeep carefully so that the oil doesn’t spill.
7. Dispose the previous o ring of the oil filter and clean the surrounding.
8. Attach the new oil filter to the mounting plate by hand. Use lubricants on the o ring if necessary.
9. Open the oil cap and pour the proper amount of oil into the oil pan with the help of a funnel.
10. Put on the oil cap and check for any leaks in the surroundings.
11. Once sure of no leaks, start the engine.
12. After 30 seconds, check the dipstick level. If there is still room for more oil according to the dipstick level, add more oil to the pan.

FAQs.

Let’s take a look at some more information regarding the Jeep Renegade oil life meter. These details can help when you urgently need to reset the oil life meter by yourself.

Conclusion

If you have followed this guide and successfully reset the oil life meter, the Jeep Renegade should perform perfectly. This process is easy enough to do yourself at home. 

However, if there are sensor issues which lead to the oil life meter flashing continuously, you should contact an expert to check it out. 

Sometimes, they might detect more underlying issues which need to be resolved as soon as possible.